Melt Flow Indexer

Product Details:

It is an affordable tabletop instrument that tests the melt mass-flow rate (MFR) of a wide range of thermoplastic raw materials, in the form of granules, strips etc. The tester is far superior to all national and international standards of Melt Flow Rates requirements. This product has been CE certificated.

Features :

• Touch screen control.
• Fast heating rate, high temperature accuracy. With upper limit protection, sound notification functions.
• Software has the functions of setting parameter, constant temperature control, cutting sample, calibration, setting test time as well as test result display.
• Password verify is necessary for important operations in case of mishandle.

 

Product Details:

It is an affordable tabletop instrument that tests the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of a wide range of thermoplastic raw materials, in the form of granules, strips etc. The tester is far superior to all national and international standards of Melt Flow Rates requirements. This product has been CE certificated.

Features

• LCD display the test result, l micro printer may print out the MVR result.
• With the functions of test temperature display, upper limit protection and sound notification. Thanks to the advanced PID controller and high resolution sample circuit, the temperature can ramp up to the set point with slight overshoot and high accuracy in stability.

 

Product Details:

 

It allows for the measurement of melt mass-flow rate (MFR) and melt volume-flow rate (MVR), melt density test according to the standards ASTM D1238, ISO1133(method A and B).

Features :

• It allows for the measurement of melt mass-flow rate (MFR) and melt volume-flow rate (MVR), melt density test according to the standards ASTM D1238, ISO1133(method A and B).
• 8"high resolution touch screen allows for fast & accurate input of test parameters and continuous display of settings during testing, printing the test result by a micro-printer.
• With the additional function of loading the Weight automatically.
• Can be connected to a PC through a RS232 port for direct acquisition of test parameters and results which can be directly saved or exported with the SW included in the supply.

 

Product Details:

It is an affordable tabletop instrument that tests the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of a wide range of thermoplastic raw materials, in the form of granules, strips etc. The tester is far superior to all national and international standards of Melt Flow Rates requirements. This product has been CE certificated.
Features :

• MFR, MVR and melt density can be measured in one test.
• Touch screen control, Chinese/English operating interface.
• Fast heating rate, high temperature accuracy. With upper limit protection, sound notification functions.
• Software has the functions of setting parameter, constant temperature control, cutting sample, calibration, setting test time, test result display, calculating melt density, as well as checking & printing test datum.
• Password verify is necessary for important operations in case of mishandle.

 

Product Details:

It is an affordable tabletop instrument that tests the melt mass-flow rate (MFR) of a wide range of thermoplastic raw materials, in the form of granules, strips etc. The tester is far superior to all national and international standards of Melt Flow Rates requirements. This product has been CE certificated.

Features

• LCD display the test result, micro printer may print out the MVR result. With the functions of test temperature display, upper limit protection and sound notification.
• Thanks to the advanced PID controller and high resolution sample circuit, the temperature can ramp up to the set point with slight overshoot and high accuracy in stability.

 

Product Details:

The Melt Flow Indexer is related to the melted material viscosity. It allows the operator to make an estimation of " mean molecular weight", at the same time gives an indication of "melt flow ability" through a die.

The melt index is defined as the weight or the volume of melted material flowing through a calibrated die, under the effect of a pre-determined force, at constant temperature and for the total time of 10 minutes.

Features :

1. Two-zone band heater
2. Touch-screen control
3. Quick die release
4. Moveable oven for easy clean
5. Cut the extrudate automatically at user preset intervals
6. Powerful data analysis and control software
7. CE Mark

Flow Rate Ratio (FRR)

Allow users to determine flow rate using two or three different test loads on one charge of material.

Motorized weigh loading

Motorized weight lifting and lowering device that further automates the testing procedure, desired weights are safely and automatically applied to the piston at a user selected time interval.

User friendly interface

Touch screen with simple set-up of test and operation. 
Connected to PC through RS232 for direct acquisition of test parameters and test results.

Multiple test results

1. FFR
2. Shear stress
3. Shear rate
4. Apparent density
5. Diagram MVR vs Time
6. Diagram MVR vs Time

Temperature

• Temperature working range: 50oC to 450 oC
• Temperature rising time: <30min
• Temperature fluctuation: ± 0.5 oC
• Temperature display error: ≤± 0.2 oC
• Temperature recovery time: <4min
• Accuracy of timer: 0.01s
• Cut-off time interval: 1-36000s

Displacement

• Encoder for piston displacement detection (MVR)
• MVR measurement accuracy: ±0.03%F.S
• Piston displacement accuracy: 0.02 mm
• Piston displacement resolution: 0.005 mm

Weights

• Automatic application of the selected weights
• On board multi-weight system including following weights:0.325, 1.20,2.16, 3.80,5.00, 10.00, 21.60 kg
• Accuracy of weight: ± 0.5%

Power supply

• Power supply:(220-15% ∼220+10%) VAC 50Hz 800W

Dimension/weight

• Dimension (L x W x H) :(630 x 690 x 1500) mm
• Weight: About 180kg

 

Product Details:

It allows for the measurement of melt mass-flow rate (MFR) and melt volume-flow rate (MVR), melt density test according to the standards ASTM D1238, ISO1133(method A and B).

Features:

• It allows for the measurement of melt mass-flow rate (MFR) and melt volume-flow rate (MVR), melt density test according to the standards ASTM D1238, ISO1133(method A and B).
• 8"high resolution touch screen allows for fast & accurate input of test parameters and continuous display of settings during testing, printing the test result by a micro-printer.
• With the additional function of loading the Weight automatically.
• Can be connected to a PC through a RS232 port for direct acquisition of test parameters and results which can be directly saved or exported with the SW included in the supply